Showing posts with label Acetylene. Show all posts
Showing posts with label Acetylene. Show all posts

Tuesday, October 24, 2023

Ranger Biodiesel Swap - Alternator Adapters

 To simplify wiring, I decided to mount the original Ford alternator on the VW engine. There's no tensioner pulley for the serpentine v-belt, so I fabricated a hinged adapter and tensioning rod.


The first version of the hinged adapter was made from billet aluminum. 




Next, I turned an aluminum v-belt pulley on my lathe, to match to profile of the original VW pulleys.







Finally, I bent a steel bracket that curves around the outside of the alternator and bolts to the engine block. With an 8mm socket cap bolt and fender washers, I made a tensioner that pulls the belt tight, rather than pushes.


After installing the engine, I discovered that the alternator was hitting the steering u-joint and needed to be rotated higher. The aluminum hinge was at its limit of travel, so I made a replacement out of steel that allowed better clearance.









Saturday, August 30, 2014

Steam Engine Restoration Part 10 (Video Post) - Casting New Babbit Bearings

After months of research and watching tutorial videos, I finally took the plunge and started the process of casting fresh crankshaft bearings for my steam engine.



This engine uses Babbitt bearings on the crank, which are cast in place between the structure of the machine and the rotating shaft it will be carrying. These were extremely common in old industrial machinery and engines of all types because they could be easily made to a high tolerance using basic hand tools.

Engines that utilize these bearings have hollow bearing blocks, which act as cups that hold the finished bearing in place. To cast the bearing, the rotating shaft is placed into the bearing block and suspended in the correct location using shims or collars. I machined a pair of steel shims that rested on the edge of the bearing block and held the crank vertically in place.

Crankshaft locating shims

The steam engine base with crank shims installed
I purchased a used casting ladle off of Craigslist and melted down the Babbitt metal brick using the propane forge. This burner maintained steady heat and quickly liquefied the brick. 

Finally getting to use the propane furnace!

Melting the Babbitt brick
 I packed clay between the bottom of the crank and the bearing block and poured the molten Babbitt into the cavity (detailed above in the video). After cooling and trimming down the excess material, the bearings were ready for test fitting. The next step is to pour the bearing cap bearings.

Trimmed and installed in the bearing blocks

Bearing halves removed for cleaning


The crankshaft installed in place for test fitting.

Thursday, March 27, 2014

Steam Engine Restoration Part 6 - Stripping the Main Bearings

The main bearings in this steam engine are made of poured babbitt metal. Bearings of this type are formed in place by loosely assembling the bearing caps with the crankshaft installed and supported at the correct assembly location. After everything has been properly located, the open gaps between the bearing blocks and the shaft are sealed with clay, and molten babbitt metal is poured in through the lubrication hole. 

Once the metal hardens, it is trimmed and scraped to its final shape. Finally, before the bearing enters service, it is cleaned, well-lubricated, and "run-in", which is a process of slowly turning the shaft and allowing the bearing to develop a wear pattern that matches the microscopic contours of the shaft surface.

The bearings in this engine were in extremely worn condition and needed to be replaced, so I used a torch to melt out the old bearing material. Then, I sandblasted, painted, and reinstalled the caps. Once the crank has been rebuilt, they can be rebabbitted.

Original condition


Removing the babbitt

Fully removed

Ready for sandblasting


Sandblasted and ready for paint


Freshly restored bearing caps installed on the engine

Saturday, December 14, 2013

CL450 Racer - Repairing the Seat

To finish retrofitting my CL450/CB500T racer into a more usable road bike, I decided to axe the current racer seat and install an original seat. Unfortunately, I never had an original one, and good examples are getting rare and expensive, so I settled for a $10 example scrounged from an estate sale at an upstate New York junkyard. The pan was mostly solid except for the rear right edge, which had effectively disintegrated. However, there was enough left to repair it.

Almost looks okay...


But it was all lies!

The back corner was completely gone.

Removing the damaged portions


Reinforcing the seat strap stud



Fabricating a replacement section



Brazing on the new section





Applying braze to both sides of the joint.



Fully sandblasted

Making new upholstery hooks


Brazing on the upholstery hooks



Applying rust-proof paint.


Covering the rust stains on the cushion.



Applying contact cement



Applying the new cover



Finished and Installed!