Showing posts with label Ignition. Show all posts
Showing posts with label Ignition. Show all posts

Thursday, August 25, 2022

Ranger Biodiesel Swap - Fuel Pump Override Switch

My Ranger is a 1999 model, equipped with a standard OBD2 system that monitors emissions and onboard mechanical diagnostics. To avoid this added complexity, most diesel swaps are performed on pre-OBD2 vehicles, or the builders will seek to remove/bypass/reprogram the ECU. 

For my build, I'm trying to retain as much of the ECU functionality as possible, and my goal is to pass the NJ MVC inspection honestly, with minimum codes and without an illuminated check engine light. 

In preparation for the swap, I'm making a number of modifications to the truck's electrical, fuel, and exhaust systems. The first of these will be described below, where I'm installing a fuel pump override switch.

The Ford Ranger ECU is programmed to run the fuel pump for approximately two seconds when the ignition is switched on, to prime the fuel injection system in preparation for engine startup. After this, the pump is shut-off until the ECU detects that the engine is running at sustained idle.

I'm replacing the original fuel system (single fuel line, regulator/return inside the tank, internal fuel pump) with a complete recirculating system featuring both sending and return lines, an external pump, and a water separator/filter. 

This type of system requires sustained operation of the fuel pump prior to startup, to circulate fuel and purge all trapped air from the lines. Rather than bypass the original fuel pump controls and wiring, I decided to install an override switch.


As shown on page 24-1 of the Ford Ranger Electrical Manual, the fuel pump is powered by the switched-side of the Fuel Pump Relay, through the Inertia Fuel Shutoff Switch, and on to connector C422 on page 24-7. 

The coil-side of the Fuel Pump Relay is connected to +12VDC on one side, and ECU Pin 80 on the -12VDC (Ground) side. To run the pump, ECU Pin 80 is switched to ground (logic output 0), which completes the circuit and triggers the relay coil. Therefore, an override switch simply needs to connect the existing Pin 80/Fuel Pump Relay wire to a switch, which can manually ground the circuit. 

Step 1: Shut off the truck, remove the connector from the ECU (engine bay on top of firewall), remove the protective covers and tape, and identify the wire connected to Pin 80.


Step 2: Carefully remove a 1/2" stretch of insulation from the wire on Pin 80 (do not cut the wire!!), wrap the stripped end of a new override switch wire around it, solder the joint thoroughly, and wrap the exposed conductors with electrical tape.

Step 3: Tuck the wires back inside the protective covers, including the new override switch wire. Route the new wire along the original harness and through the firewall of the truck, and rewrap the covers with electrical tape.


Step 4: Install a SPST toggle switch in the cab, and connect one side to the override switch wire that was just pulled though the firewall. Connect the other side to a wire that is grounded to the truck chassis.



This switch will now allow the driver to manually override the fuel pump at any time, without altering the original wiring or throwing any OBD2 codes.

Sunday, October 4, 2015

Diesel Land Speed Racer Mk2 - Part 6 - Starting and Stopping


The engine in the Diesel Sportster is 3 times larger than the engine in my first bike, so it requires an electric starter and a fuel pump to operate correctly. It also has a heavy-duty solenoid that holds the governor open, and snaps closed to shut the engine down when the kill switch is used. These are all relatively high-amperage systems, so a single fuse and normal switches were not enough to safely control them. 

For the electrical system, I used a marine-grade 6-fuse block and a pair of automotive relays. The fuses protect every individual circuit which will simplify troubleshooting, and by using relays I can avoid sending high amps through the relatively fragile handlebar switches. All of the wires are color-coded, with yellow wires for the starter system, white wires for the governor solenoid, red for main power, black for control switch power, and green for ground.

The fuel pump is another marine-grade unit which is rated for most types of fuel, including biodiesel.







Now that starting was done, it was time to focus on stopping. The original Harley calipers suffered an extreme design flaw. The bolts that held them to the swingarm screwed into nuts that were captured in hexagon-shaped holes in the alloy caliper body. Unfortunately, when these need to be removed and rebuilt, the bolts have inevitably seized from rust and the nuts tear open the hexagonal holes, wrecking the casting and making it impossible to tighten the bolts correctly during reassembly.

The caliper I purchased (for cheap) of course had been discarded because of this damage. I drilled out the old shoulder bolts, milled the hexagon holes round, installed steel spacers to keep the new nuts from gouging into the alloy caliper body, and installed modified 7/16 diameter socket-cap bolts and locking nuts.






NOS replacement bolts, which were unusable because the chrome was flaking off.

Final installation.

Saturday, April 11, 2015

CL450 Racer - Prepping For Loring 2015 Part 3

T-minus 12 days to leaving for Loring, and I am posting a quick update of the prep progress.

I installed the PAMCO, but ran into some problems setting it up. After a few weeks of little success and even less sleep, I ditched the electronic ignition and went back to the original condensers and points.

I also replaced the Dunlop K70 semi-knobbies with a pair of race-legal Dunlop K81 Roadmaster TT100's. These tires have an unbroken center ridge in the tread. When over-inflated to about 60psi, the tire contact area is extremely small, greatly reducing rolling resistance.

Finally, I discovered that the cam chain tensioner was stuck and had not properly auto-adjusted during the last two or three engine tune-ups. As a result, the cams were slightly out of time, and the chain had ground quite a bit of fine aluminum dust into the crankcase oil. After 6 oil changes, and running the engine each time to flush out the dust, the oil is now (moderately) clean once again, and the engine is making no strange noises.


The box of supplies and fire-suppression


Wednesday, February 18, 2015

CL450 Racer - Prepping For Loring 2015 Part 2

After waiting on parts for a few weeks, over the weekend I finished wiring and installing the PAMCO ignition system. 

The installation first involved attaching connectors to the wires and covering them with heat shrink tubing (to both protect and stress-relieve them). Next, I made a small bracket to attach the Electronic Advance Module, sealed the module with liquid electrical tape to keep out moisture, and zip-tied everything in place. After this, all that was left was to time the ignition with the help of my friend and a Timing Strobe.

In addition, rather than apply the race registration numbers to the tank, I fabricated some brackets and installed number boards under the seat. Now all I need is warm weather!
PAMCO Ignition Installed

Air Intake Cover with appropriate warning

Number Board Bracket

Ignition Advance Module Bracket

Sealing the Advance Module from Moisture

Mounting the Advance Module Under the Seat

Wiring Harness Adapter for the Electronic Ignition

Ready For Testing and Tuning....once the snow melts.

Saturday, January 31, 2015

CL450 Racer - Prepping for Loring 2015 Part 1

After taking the 2014 race season off, I immediately started 2015 by prepping my CL450 for the Spring Event at the Loring Timing Association. Modifications are relatively light this year, and are mostly focused on the ignition and exhaust systems. I picked up a pair of EMGO reverse-cone megaphones and a PAMCO electronic ignition system, and will be installing and tuning for them over the next few months.

Reverse-Cone Megaphone

Wide open and LOUD


Original Points Ignition

PAMCO ignition loosely installed

Sunday, June 22, 2014

BSA Bantam - Rebuilding the Ignition Timing Plate

The last major repair for the engine was to fix the worn-out points and points plate bushing. The reproduction points cam that I purchased had not been correctly finished, and had a sharp edge at the beginning of the cam lobe instead of a smooth curve. 

The points arm, literally eaten away by the sharp edge.

The points timing cam. The sharp transition is clearly visible.
A points cam should have a much smoother transition, such as the one seen here on a CB450 cam:

Smooth with no sudden transitions
I had a machine shop carefully smooth out the edge with a fine tool grinder.

Refinished cam lobe

The sharp transition is completed smoothed out
After fixing the cam, I had to replace the bronze bushing in the points plate. This bushing supports the end of the crankshaft and keeps it dead center relative to the points arm. It also prevent the crankshaft end from wobbling, which has been known to cause metal fatigue failures and ruin the crankshaft. I pressed out the oil bushing with a large screw and hammer:



Successfully removed

Brand-new bushing


Bushing installed.
After pressing out the bushing, I installed the new bushing in its place, using a large amount of Loctite 680 to lock it into place. I reassembled the points, re-timed the engine, and now it starts on the second kick every time.

Tuesday, September 10, 2013

Friday, September 6, 2013

BSA Bantam - Homemade 12V Ignition System

When I bought my Bantam Trail Bronc it was, lets say, a bit rough:

50 bucks, but the tetanus was free!
At that point, maintaining originality wasn't my concern. Just getting it running again would be a big enough hassle, so I left it mostly as is, and gave it a full engine rebuild and some new tires.


I won't get into the details on the engine build today, because that could take up several posts. I could write for pages about that job, so instead, I'm gonna focus on the modernized electrical system that I installed.

The original system was a low output flywheel ignition coil. I replaced all the bits with aftermarket parts, and was able to get the thing running:

BSA Bantam First Start

And then, after that? Nothing. The bike never started again. It sat in my garage for a year while I rechecked, modified, and adjusted every possible part. I never suspected the coil because, well, it was brand new, and the plug sparked whenever I held it against the case. Then, 3 weeks ago, I tried the same process yet again, holding the plug against the case and kicking it over. Amazingly, at that exact moment, the coil which had apparently been internally shorting all along completely died and produced no more spark. Eureka!

It turns out that if the output is too low, a plug that sparks freely when held in open air may not necessarily spark inside the engine, where the gasoline wets it down. Before rebuilding, I wanted to precisely set the spark timing, but do away with the need for a timing disc. I modified a used spark plug with an adjustable screw and a soft aluminum cap and then inserted into the plug hole.



I carefully turned the crank until the piston hit the plug, and drew a reference line on the flywheel aimed at tab on the case. I then repeated this in the other direction, and punched a reference line between the two pencil lines. This marks top dead center.


 Next, I marked the location of the proper firing position, about 16.5 degrees before TDC, and marked that, as well as labeling it.


Next up was the electrical bits. I stripped out the coil and magneto core, and reused the stock points and condenser with new wiring.


I used these to trigger an aftermarket 12V Yamaha ignition coil that I mounted next to an original Bantam battery tray. I wired it all up and used a miniature hobby 12V battery to power the whole system.




Now it will reliably start on the second or third kick. I will have to take some video as soon as possible.